Mountain bike trials
Photograph by Felixeon Flickr.
The rider bike s hands must remain on the handlebars. Maximum obstacle jump Mountain bike trials heights are specified, from 0.80 to 1.80 metres depending on category.
The UCI rules were changed to this format after too many competitions ended Tall bike in a draw and riders were forced to ride an extra section. Certain rules enforce the number of points gained within a section, for Mountain bike trials example, putting both feet down or a hand will result in 5 points.
Both sides of the course are marked with plastic tape, and there must be a clear stretch of 3 metres prior to the finish line, in order to prevent riders jumping over the line from Mountain bike trials an obstacle. The most common way to gain a point is by putting a foot down within a section; for this reason points are sometimes known as dabs .
UCI rules also allows riders to compete in both mod and stock categories. When a rider is in a Mountain bike trials section, neither tire is allowed to cross the side boundary tape even if the wheel is in the air. As a result of being based on BMX bikes, the rear dropout spacing is 116mm.
Brakes must be more powerful than standard bicycle brakes in order to prevent the wheel from moving when hopping on uneven surfaces. The sections, each approximately 60m in length, are laid out on a circuit to allow riders to ride from one section to the next, but whether the sections have to be completed in order depends on the individual competition. The spacing of the drop outs is 116mm, the same as on a mod trials bike. Cross-country · Downhill · Freeride · Dual slalom · Four-cross · Marathon · 24 hour · Enduro · Epic · Trials .
On the front wheel, good brake modulation is usually the goal, whereas in the rear, maximum braking power is more important. UCI regulations stipulate that a course consist of at least 14 sections per course, including repeated sections. Tires and rims are wide allowing low pressures and increased contact and grip.
Before beginning a section, a rider is allowed to walk through it, and examine all the elements, but must not enter it with their bike. The UCI Mountain Bike & Trials World Championships are held annually and crown a 20-inch and 26-inch wheel trials world champion. The rules are unlike UCI scoring and parts of the bike (for example, bash guard or bash ring, cranks and pedals) can rest on an object without resulting in a dab . Mountain bike trials, also known as observed trials is a discipline of mountain biking in which the rider attempts to pass through an obstacle course without setting foot to ground.
The level of riding for the elite 20″ class is regarded as the highest in bicycle racing since the section beginner is set at the highest technical level. The rules are the same as the BIU but only people belonging to a club or school can compete in these, these are for lower level students to learn how to compete. Trials bikes are often designed without regard for attaching a seat. Exceeding the time limit for the course will either result in 5 points (BIU rules) or an additional point for every 15 seconds over the limit (UCI rules). Within UCI rules, if any part of the bike except the tires touch any object in the course, a dab will be given.
These specific sizes were adopted from previously available bikes. The first purpose made and commercially available trials bikes were manufactured by Montesa a mototrials company and were based on the modified bmx bikes that riders had been using. Derived from motorcycle trials, it originated in Spain and is said to have been invented by the father of Ot Pi, a world champion motorcycle trials rider.
Skills taken from trials riding can be used practically on any bicycle for balance, for example controlled braking and track standing, or balancing on the bike without putting a foot down. It now has a strong — though small — following worldwide, though it is still primarily a European sport.
Horizontal dropouts become more and more common. These bikes have 24 wheels and usually have horizontal dropouts, although they are spaced to fit a 135mm hub as on a 26 bike. Competition trial bikes are characterised by powerful brakes, wide handlebars, lightweight parts, single-speed low gearing, low tyre pressures with a thick rear tire, distinctive frame geometry, and typically a lack of seat. The general principle in a bike trials competition is to ride a number of pre-marked sections (usually 2 laps of 10 sections or 3 laps of 7 sections), the winner being the rider with the fewest points at the end of the competition. Currently there are two official types of competition rules, enforced by the UCI and BikeTrial International Union. The maximum number of points that can be obtained in each section is 5, the lowest (and best) score is 0 points or clean .
Gear ratios are lower than on most bicycles in order to provide the power and quick acceleration needed to move the bike at the typically low speeds of trials riding. According to current competition standards there are two classes of trials bike recognized. 26″ used to refer to mountain bike kept in original condition.
They are not legally allowed to compete in competitions but suit riders with a more street style. At most two sections can be composed entirely of artificial elements.
The spacing of the dropout is often smaller, to fit the rear hub of a 20 bike. (e.g.spins, manuals, bunnyhops) Trial riding requires very good brake control, and as a result, bicycle trials riders sometimes have unusual brakes.
26″ classed bikes were required to have at least six working gear ratios and a seat. These 20″ wheeled trials bikes have become known colloquially as Mod bikes. Early mountain bikes were well suited to the trials riding being done and so a separate class was introduced for them.
Pi s father had wanted his son to learn motorcycle trials by practising on an ordinary push bike. Trials riding is an extreme test of bicycle handling skills, over all kinds of obstacles, both natural and man-made. There is a subcategory of Stock trials bikes, sometimes called Modstock Bikes : these bikes have 26 inch wheels but have horizontal dropouts like on mod bikes as opposed to vertical dropouts on stock bikes.
Now, however, this designation is often used to describe any trials bike with 26″ wheels. As the distinguishing characteristic of the classes is the bike s approximate wheel diameter, the classes are known as 20″ and 26″.
